Extreme Networks 10GB-AC05-SFPP Compatible 10G SFP+ Active Copper Twinax Cable, 5m (16ft)

The product on this page is the 5m (16ft) version of Extreme Networks 10GB-AC05-SFPP, built for 10G operation with SFP+ to SFP+. Its complete ACC construction simplifies the physical link, and the sections below cover the exact specification, rack-integration considerations and factory verification for this individual order code.

OEM Part Number: 10GB-AC05-SFPPHT Part Number: 10GB-AC05-SFPP

Product Highlights

Compatible alternative to Extreme Networks 10GB-AC05-SFPP
10G connectivity at 10Gbps
Interface configuration: SFP+ to SFP+
Fixed length and part number: 5m (16ft), 10GB-AC05-SFPP
Cable construction: Active Twinax
Conductor specification: 28AWG
Maximum power consumption: ≤0.5W
Minimum bend radius: 30mm

Specifications

HT Part Number	10GB-AC05-SFPP
Extreme Networks Compatible	10GB-AC05-SFPP
Manufacturer	HT
Connector Type	SFP+ to SFP+
Max Data Rate	10Gbps
Minimum Bend Radius	30mm
Wire AWG	28AWG
Cable Length	5m (16.4ft)
Jacket Material	PVC (OFNR)
Cable Type	Active Twinax
Temperature	0 to 70°C (32 to 158°F)
Power Consumption	≤0.5W
Power Supply	3.3V
Protocols	1x InfiniBand QDR, DDR, SDR, 10 Gigabit Ethernet, Fibre Channel

Power and Thermal Planning

The rated power consumption is ≤0.5W. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.

Cable Construction and Routing

This assembly uses 28AWG conductors, PVC (OFNR) jacket, minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.

Network and Protocol Considerations

The intended application is determined by the host interface and protocol support. Listed interface and protocol references include 1x InfiniBand QDR, DDR, SDR, 10 Gigabit Ethernet, Fibre Channel. Confirm that the host firmware and port configuration support the same operating mode.

Length Selection and Installation Planning

The 5m (16ft) length gives 10GB-AC05-SFPP more freedom for adjacent-rack and row-end deployments. Longer copper runs need particular attention to routing weight and bend control; the ACC specification and host support must still match the intended link.

Position Within the Length Range

10GB-AC05-SFPP occupies the middle of this family between 10GB-AC03-SFPP at 3m (10ft) and 10GB-AC07-SFPP at 7m (23ft). It adds 2m over the shorter option for extra routing clearance, while the next longer version adds another 2m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.

Data-Center Design and Airflow

Select the assembly by both reach and rack layout. A direct connection removes separate module-and-patch-cord interfaces, but it still needs a bend-safe pathway and clear connector access. Keep cable bundles from blocking front-panel airflow, account for the listed interface power where applicable and choose a length that supports maintenance without leaving an unmanaged coil. For this assembly, the listed conductor specification is 28AWG; the minimum bend radius is 30mm; the stated power consumption is ≤0.5W; the jacket material is PVC (OFNR).

Quality Assurance and Packaging

Each cable receives connector inspection and a functional link check before it is coiled with bend-safe slack and packed. Protective materials shield the connector housings during transport. Rack or project labels are available to keep length, part number and installation destination aligned. Volume orders can include customer references on the labels and carton list.

Ordering Information

Provide the OEM reference, HT part number, fixed length and quantity, together with the intended host interfaces. Rack-based quantities and packaging instructions can be included for larger deployments. Other lengths are separate products and should be entered on their own order lines. Keep 10GB-AC05-SFPP associated with 5m (16ft) throughout the order and receiving record.

Extreme Networks Compatibility and Factory Testing

Compatibility confirmation combines host identification with actual link establishment and diagnostic checks. The assembly is prepared for the stated OEM reference rather than selected only by connector shape. For a new data-center deployment, the equipment model, port mode and software release provide the most useful basis for a pre-order review. Both connectors are examined before the operating test, which includes link stability and diagnostic indications.

Frequently Asked Questions

Is this an original Extreme Networks cable?

No. It is an HT-manufactured compatible alternative for equipment that specifies Extreme Networks 10GB-AC05-SFPP.

Will any matching connector operate at the same speed?

Not necessarily. Both hosts must support the stated rate, identification, lane mapping and any required breakout configuration; mechanical compatibility alone is insufficient.

What details assist a compatibility review?

Provide the equipment manufacturer, model, port type, hardware revision and software release, together with the OEM reference, required length and quantity.

How should an unused assembly be stored?

Protect both connector ends, keep the cable in a loose bend-safe coil and retain its part-number label so the length and compatibility identity remain traceable.

Shipping and Lead Time

Available stock is generally dispatched within one to three working days after order confirmation, with production lead times advised for larger quantities. Delivery can be arranged by courier, air freight or sea freight, and goods may instead be handed to an appointed forwarder or shipped on the customer’s courier account.