50G SFP56 AOC

The 50G SFP56 AOC series provides 50Gbps direct-attached connectivity using the interfaces shown in the specification table. The assembly combines integrated optical interfaces and factory-attached multimode fiber in one tested product. This page covers the family rather than a single length, with standard options of 1m (3ft), 2m (7ft), 3m (10ft), 5m (16ft), 10m (33ft), 15m (49ft), 20m (66ft), 25m (82ft), 30m (98ft), 50m (164ft) and custom project lengths available for review.

Series Part Number: SFP-50G-AOManufacturer: HT

Product Highlights

the interfaces shown in the specification table direct-attached interface arrangement
Supports 50Gbps links
Standard lengths: 1m (3ft), 2m (7ft), 3m (10ft), 5m (16ft), 10m (33ft), 15m (49ft), 20m (66ft), 25m (82ft), 30m (98ft), 50m (164ft)
Factory-tested complete cable assemblies for enterprise, operator and data-center installations

Available Lengths

Available standard configurations include 1m (3ft), 2m (7ft), 3m (10ft), 5m (16ft), 10m (33ft), 15m (49ft), 20m (66ft), 25m (82ft), 30m (98ft), 50m (164ft). Select a length that follows the managed route without pulling on either connector or leaving excessive slack around airflow paths. Custom lengths can be manufactured for projects when the standard range does not match the installation.

Specifications

Series Part Number	SFP-50G-AO
Part Number	SFP-50G-AO01
Manufacturer	HT
Form Factor	SFP56
Max Data Rate	50Gbps
Cable Type	Optical Cable
Max Cable Distance	Up to 50m
Available Length Options	1m (3ft), 2m (7ft), 3m (10ft), 5m (16ft), 10m (33ft), 15m (49ft), 20m (66ft), 25m (82ft), 30m (98ft), 50m (164ft)
Minimum Bend Radius	60mm
Power Consumption	≤2W
Jacket Material	OFNP
Receiver Type	PIN
Transmitter Type	VCSEL
FEC Function	Support Pre-FEC
CDR	TX+RX
Modulation Format	PAM4
Temperature	0 to 70°C (32 to 158°F)
Protocol	IEEE 802.3cd SFP56 MSA

Applications and Cable Routing

This 50G AOC series can be used for suitable switch-to-switch, switch-to-server and rack interconnection requirements. Measure the actual pathway through horizontal and vertical managers before choosing a length. Keep connector boots clear of sharp edges, observe the stated bend limit and leave enough access to release each latch during maintenance.

Compatibility and Factory Testing

Compatibility depends on the host interface, operating mode and the identification required by the equipment. For brand-coded versions, provide the equipment model and OEM reference so the intended configuration can be reviewed before production. Each complete assembly is inspected at both ends and checked for link operation; optical versions also require clean, protected interfaces throughout installation.

Ordering Information

Quote the SFP-50G-AO series together with the required length, host brand, OEM reference where applicable and quantity. Mixed-length projects should use a separate order line for each configuration. Project labels and packaging can identify rack locations or endpoint assignments to make receiving and later maintenance easier.

Related Product Configuration

Additional factory information for this cable family is available on the 50G SFP56 AOC configuration page. You can also compare adjacent assemblies in the 50G AOC cable collection.

Quality Assurance and Shipping

Connector condition, assembly identification and functional link behavior are checked before protective packing. Standard configurations are prepared for dispatch as quickly as stock allows, while larger or customized orders receive a confirmed production schedule. Local and international delivery options are available.

Frequently Asked Questions

Does this page represent only one cable length?

No. It describes the product series and lists the standard length options. Confirm the exact length and corresponding order reference when requesting a quotation.

Are separate transceivers required?

No. The cable and its attached interfaces form one complete direct-attached assembly and are tested together.

Can a custom length or brand-compatible version be supplied?

Yes, subject to configuration review. Provide the required length, equipment model and OEM part number so compatibility and production details can be confirmed.