Cisco QDD-4ZQ100-CU Compatible 400G QSFP-DD 8 x 50G PAM4 to 4 x 100G QSFP56 2 x 50G PAM4 Passive Copper Breakout Cable

Product Highlights

• HT-manufactured compatible alternative for Cisco QDD-4ZQ100-CU
• 400G aggregate connectivity at 400Gbps
• Interface configuration: QSFP-DD to 4x QSFP56
• DAC / Copper
• Length configurations covered: 0.5m (2ft), 1m (3ft), 1.5m (5ft), 2m (7ft), 2.5m (8ft) and 3m (10ft)
• Conductor specification: 28AWG
• Power consumption: 0.1W (QSFP-DD End)0.1W (QSFP56 Per End)
• Operating temperature: 0 to 70°C (32 to 158°F)

Available Lengths and Corresponding Part Numbers

The documented configurations are 0.5m (2ft), 1m (3ft), 1.5m (5ft), 2m (7ft), 2.5m (8ft) and 3m (10ft). Each link below opens the separate product page for that physical length and its corresponding OEM part number. Select the exact assembly required by the route and purchase order; custom project lengths can be discussed separately.

Compatible OEM Part Numbers

• QDD-4ZQ100-CU0.5M
• QDD-4ZQ100-CU1M
• QDD-4ZQ100-CU1.5M
• QDD-4ZQ100-CU2M
• QDD-4ZQ100-CU2.5M
• QDD-4ZQ100-CU3M

Specifications

Applications and Deployment

A passive DAC reduces the connection to one factory-terminated electrical assembly. This is useful where low latency, low interface power and a short managed route matter more than optical reach. Cable gauge, connector construction and host port settings still influence whether the complete link operates reliably. For this series, the listed interface is QSFP-DD to 4x QSFP56 and the aggregate rate is 400G. The stated application is 400G Ethernet.

Quality Assurance and Packaging

Each cable receives connector inspection and a functional link check before it is coiled with bend-safe slack and packed. Protective materials shield the connector housings during transport. Rack or project labels are available to keep length, part number and installation destination aligned. Both connector ends are inspected as part of the complete assembly, and protective packing is selected to avoid tight bends during transport and storage.

Cable Construction and Routing

The specification table records the conductor specification is 28AWG; the jacket material is PVC; the minimum bend radius is 41mm; the operating temperature is 0 to 70°C (32 to 158°F); the power consumption is 0.1W (QSFP-DD End)0.1W (QSFP56 Per End). Use those values when preparing the rack pathway and receiving checklist. Do not pull a connector by its cable, compress the run under tight ties or force excess length into a sharp coil. Connector protection should remain in place until the assembly is ready for insertion.

Data-Center Design and Airflow

Select the assembly by both reach and rack layout. A direct connection removes separate module-and-patch-cord interfaces, but it still needs a bend-safe pathway and clear connector access. Keep cable bundles from blocking front-panel airflow, account for the listed interface power where applicable and choose a length that supports maintenance without leaving an unmanaged coil. For this series, keep the interface rate, DAC construction and length-specific OEM reference together throughout that review.

Ordering Information

Provide the OEM reference, HT part number, fixed length and quantity, together with the intended host interfaces. Rack-based quantities and packaging instructions can be included for larger deployments. Other lengths are separate products and should be entered on their own order lines. For this series, follow the corresponding length link, quote that exact OEM part number and keep different lengths on separate order lines. HT part number QDD-4ZQ100-CU identifies the product family; the linked page provides the final length-specific identity.

Cisco Compatibility and Factory Testing

Compatibility confirmation combines host identification with actual link establishment and diagnostic checks. The assembly is prepared for the stated OEM reference rather than selected only by connector shape. For a new data-center deployment, the equipment model, port mode and software release provide the most useful basis for a pre-order review. Series-level inspection is followed by the exact length and OEM configuration selected for dispatch. Functional verification includes link establishment and diagnostic indications where the host exposes them.

Shipping and Lead Time

Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.

Frequently Asked Questions