Brocade E1MG-SX-OM Compatible 1G SFP Transceiver Module 550m on 50 / 125µm OM2 MMF275m on 62.5 / 125µm OM1 MMF220m on 62.5 / 125µm FDDI MMF

Product Highlights

• Compatible alternative to Brocade E1MG-SX-OM
• 1G connectivity at 1.25Gbps
• Optical wavelength: 850nm
• Specified reach: 550m on 50 / 125µm OM2 MMF275m on 62.5 / 125µm OM1 MMF220m on 62.5 / 125µm FDDI MMF
• Duplex LC / MMF interface
• Digital diagnostic monitoring: Supported
• Operating temperature: 0 to 70°C (23 to 158°F)

Specifications

Applications and Optical Link Design

Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The Duplex LC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.

Before deployment, check the host port type, supported data rate and firmware requirements. The 1G interface configuration must match the remote equipment; sharing a SFP housing alone does not make two transceiver types interoperable.

For this multimode module, confirm fiber grade, modal bandwidth and total loss before commissioning. The 550m on 50 / 125µm OM2 MMF275m on 62.5 / 125µm OM1 MMF220m on 62.5 / 125µm FDDI MMF figure applies only under suitable cabling conditions. Inspect every Duplex LC mating point and match the remote optical standard.

Quality Assurance and Packaging

Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.

Optical Acceptance, Diagnostics and Handling

For this model, the specified transmit-power range is -9.5~-3dBm; receiver sensitivity is < -17dBm. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.

Data-Center Optical Design and Airflow

Select the module by optical standard, reach and rack layout. Check the complete fiber channel, including panels and connectors, and keep dense bundles from blocking front-panel airflow. Account for listed power consumption and preserve enough space to remove a module without disturbing adjacent links. For this model, the principal parameters are data rate 1.25Gbps, wavelength 850nm, rated reach 550m on 50 / 125µm OM2 MMF275m on 62.5 / 125µm OM1 MMF220m on 62.5 / 125µm FDDI MMF.

Ordering Information

Quote HT part number E1MG-SX-OM together with OEM reference E1MG-SX-OM and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.

Brocade Compatibility and Factory Testing

Compatibility testing for E1MG-SX-OM combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.

Frequently Asked Questions

Shipping and Lead Time

Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.