Brocade 40G-QSFP-C-0501 Compatible 40G QSFP+ Passive Copper Cable, 5m (16ft)

For data-center links that specify Brocade 40G-QSFP-C-0501, this 5m (16ft) DAC assembly delivers 40G connectivity through QSFP+ to QSFP+. It removes separate module-and-patch-cord interfaces while retaining clear mechanical, power and compatibility details for high-density design and installation planning.

OEM Part Number: 40G-QSFP-C-0501HT Part Number: 40G-QSFP-C-0501

Product Highlights

Compatible alternative to Brocade 40G-QSFP-C-0501
40G connectivity at 40Gbps
Interface configuration: QSFP+ to QSFP+
Fixed length and part number: 5m (16ft), 40G-QSFP-C-0501
Conductor specification: 26AWG
Minimum bend radius: 40mm

Specifications

HT Part Number	40G-QSFP-C-0501
Brocade Compatible	40G-QSFP-C-0501
Manufacturer	HT
Connector Type	QSFP+ to QSFP+
Max Data Rate	40Gbps
Minimum Bend Radius	40mm
Wire AWG	26AWG
Cable Length	5m (16.4ft)
Jacket Material	PVC (OFNR)
Temperature	0 to 70°C (32 to 158°F)
Protocols	SFF-8436, QSFP+ MSA and IEEE 802.3ba

Cable Construction and Routing

This assembly uses 26AWG conductors, PVC (OFNR) jacket, minimum bend radius 40mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.

Length Selection and Installation Planning

The 5m (16ft) length gives 40G-QSFP-C-0501 more freedom for adjacent-rack and row-end deployments. Longer copper runs need particular attention to routing weight and bend control; the DAC specification and host support must still match the intended link.

Position Within the Length Range

40G-QSFP-C-0501 occupies the middle of this family between 40G-QSFP-C-0301 at 3m (10ft) and 40G-QSFP-C-0701 at 7m (23ft). It adds 2m over the shorter option for extra routing clearance, while the next longer version adds another 2m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.

Data-Center Design and Airflow

Select the assembly by both reach and rack layout. A direct connection removes separate module-and-patch-cord interfaces, but it still needs a bend-safe pathway and clear connector access. Keep cable bundles from blocking front-panel airflow, account for the listed interface power where applicable and choose a length that supports maintenance without leaving an unmanaged coil. For this assembly, the listed conductor specification is 26AWG; the minimum bend radius is 40mm; the jacket material is PVC (OFNR).

Network and Protocol Considerations

The intended application is determined by the host interface and protocol support. Listed interface and protocol references include SFF-8436, QSFP+ MSA and IEEE 802.3ba. Confirm that the host firmware and port configuration support the same operating mode.

Passive Copper Operation

A passive DAC has no separate optical conversion stage. Its low-power, low-latency operation is useful for short equipment links, but the assembly must remain within the length and signaling mode accepted by both hosts.

Quality Assurance and Packaging

Each cable receives connector inspection and a functional link check before it is coiled with bend-safe slack and packed. Protective materials shield the connector housings during transport. Rack or project labels are available to keep length, part number and installation destination aligned. Neutral packaging and customer-specific packing documentation are available on request.

Ordering Information

Provide the OEM reference, HT part number, fixed length and quantity, together with the intended host interfaces. Rack-based quantities and packaging instructions can be included for larger deployments. Other lengths are separate products and should be entered on their own order lines. Quantity and any labeling instructions should be attached specifically to 40G-QSFP-C-0501.

Brocade Compatibility and Factory Testing

Compatibility confirmation combines host identification with actual link establishment and diagnostic checks. The assembly is prepared for the stated OEM reference rather than selected only by connector shape. For a new data-center deployment, the equipment model, port mode and software release provide the most useful basis for a pre-order review. Both connectors are examined before the operating test, which includes link stability and diagnostic indications.

Frequently Asked Questions

Is this an original Brocade cable?

No. It is an HT-manufactured compatible alternative for equipment that specifies Brocade 40G-QSFP-C-0501.

Can excess cable be folded into a compact bundle?

No. Use a supported, bend-safe service loop and observe the listed minimum bend radius. Do not crease the cable or tighten ties around the connector boots.

Will any matching connector operate at the same speed?

Not necessarily. Both hosts must support the stated rate, identification, lane mapping and any required breakout configuration; mechanical compatibility alone is insufficient.

What details assist a compatibility review?

Provide the equipment manufacturer, model, port type, hardware revision and software release, together with the OEM reference, required length and quantity.

Shipping and Lead Time

Available stock is generally dispatched within one to three working days after order confirmation, with production lead times advised for larger quantities. Delivery can be arranged by courier, air freight or sea freight, and goods may instead be handed to an appointed forwarder or shipped on the customer’s courier account.